Is it possible to DIY a sunburst guitar finish
At first developed to mimic a classic look (as identified on very old violins and mandolins) Sunburst is a classic guitar color frequently encountered upon guitars aged and newer. It's a highly desirable guitar finish but it it possible for the average person? It is possible to obtain a sunburst finish on your own guitar if you decide to follow a couple of basic steps and take your time and don't rush. It's wise for you to experiment first using a scrap part of lumber prior to moving on to the guitar.
If it is a brand new guitar kit,then construct your guitar firstly. Needless to say you will be pulling it down to work on the finish but you need to know you won't befacing potential issues with the guitar that jeopardize the finish you've specifically put a great deal of valuable time into. When you've constructed the electric guitar and analyzed for potential problems you should begin to set up the timber. Sand right back until eventually you get a totally consistent surface to apply your finish. You should get rid of unwanted dust particles and clean the guitar completely.
The next step is to administer plenty of wood grain filler. It is best to apply thickly over the face belonging to the guitar and afterwards work it in. The moment it has dried out remove and remove any excess filler with a wet rag. Now it is an opportunity to spray the back and sides of the body and neck of your electric guitar. A fundamental factor to keep in mind would be to cover up the top and fretboard. As you are spraying aerasol it's best if you keep the aerosols in quite warm water before you start using. It will demand a number of coats so do not experiment with applying too much all at one time. The key is to increase your guitar's colour layer after layer and apply from a good distance from the guitar so you achieve a feathered edge. The nearer you end up getting the more complicated the edge line you will end up with.
Following that administer the amber lacquer. Chances are you'll be obliged to mask the sides of your guitar after which you can position the guitar on a firm workbench faced upwards before applying. Upon having finished this task you should administer the clear coat after that and use your sandpaper in between coats to get rid of any issues. After that apply the next pitch-dark stain to achieve a blend of colour between the edge and inner colors. Attempt to apply exceptionally thin and amass the required coats. At this time be certain to let the lacquer dry. The moment the guitar is completely moistureless focus on sanding for a second time.
This is the final detail. The key here is to employ a more lightweight gauge of emery paper each and every time you are effectively taking out the markings because of the gauge of sandpaper administered beforehand soon after which progressing for the less heavy gauge. Remember to keep gently sanding and then moving to a less heavy gauge unless you run out of sandpaper and then move on to your buffer.About now you may just continue to keep buffing or hand polishing until you end up getting very fine for the finished look.
If it is a brand new guitar kit,then construct your guitar firstly. Needless to say you will be pulling it down to work on the finish but you need to know you won't befacing potential issues with the guitar that jeopardize the finish you've specifically put a great deal of valuable time into. When you've constructed the electric guitar and analyzed for potential problems you should begin to set up the timber. Sand right back until eventually you get a totally consistent surface to apply your finish. You should get rid of unwanted dust particles and clean the guitar completely.
The next step is to administer plenty of wood grain filler. It is best to apply thickly over the face belonging to the guitar and afterwards work it in. The moment it has dried out remove and remove any excess filler with a wet rag. Now it is an opportunity to spray the back and sides of the body and neck of your electric guitar. A fundamental factor to keep in mind would be to cover up the top and fretboard. As you are spraying aerasol it's best if you keep the aerosols in quite warm water before you start using. It will demand a number of coats so do not experiment with applying too much all at one time. The key is to increase your guitar's colour layer after layer and apply from a good distance from the guitar so you achieve a feathered edge. The nearer you end up getting the more complicated the edge line you will end up with.
Following that administer the amber lacquer. Chances are you'll be obliged to mask the sides of your guitar after which you can position the guitar on a firm workbench faced upwards before applying. Upon having finished this task you should administer the clear coat after that and use your sandpaper in between coats to get rid of any issues. After that apply the next pitch-dark stain to achieve a blend of colour between the edge and inner colors. Attempt to apply exceptionally thin and amass the required coats. At this time be certain to let the lacquer dry. The moment the guitar is completely moistureless focus on sanding for a second time.
This is the final detail. The key here is to employ a more lightweight gauge of emery paper each and every time you are effectively taking out the markings because of the gauge of sandpaper administered beforehand soon after which progressing for the less heavy gauge. Remember to keep gently sanding and then moving to a less heavy gauge unless you run out of sandpaper and then move on to your buffer.About now you may just continue to keep buffing or hand polishing until you end up getting very fine for the finished look.
About the Author:
Before you buy anything, Vsit us: website at www.eguitarkits.com for information. Guitar Kits and general tips on finishing.
